1800 287 223 · info@astcad.com.au

Structural drafting services in Brisbane.

Structural drafting for Brisbane engineers, builders and steel fabricators, drawn to AS 4100 from your sketches, models or markups. Our core team is based in Brisbane.

Structural drafting services Brisbane - ASTCAD
Structural drafting for Brisbane projects, from single drawings to full packages.
Projects
650+
Standards
AS 4100
Quote
1 day
Since
2010
Software
TeklaSolidWorksAutoCADRevit

Structural drafting for Brisbane engineers

ASTCAD prepares structural drafting for Brisbane engineers, builders and steel fabricators: steel shop drawings, connection details, reinforcement drawings and as-builts, drawn from the engineer’s design.

Brisbane is home ground. Most local jobs are steel for houses on sloping blocks, sheds, mezzanines and light commercial buildings: the fabricator gets drawings to cut and weld from, and the engineer gets a set that matches the structural design.

What we draw

Steel shop drawings

General arrangement, assembly and single-part drawings a fabricator can cut and weld from.

Connection details

Cleats, end plates, base plates and bracing connections detailed to the engineer’s design.

Reinforcement drawings

Slab, footing and wall reinforcement with bar schedules.

Stairs, platforms and handrails

Access steelwork detailed with AS 1657 in mind.

Cutting files and material lists

DXF or NC files for the cutting line, with a material list for ordering.

As-built and site-measure drawings

Existing steel measured and drawn so new work can be fitted to it.

What shapes structural drawings in Brisbane

Queensland regulates engineering directly. Under the Professional Engineers Act 2002, professional engineering services in or for Queensland must be carried out by a registered professional engineer (RPEQ) or under an RPEQ’s direct supervision. Our drawings are prepared to your RPEQ’s design and go back to them for review before issue.

  • Registration: the Board of Professional Engineers of Queensland keeps the RPEQ register. Member sizes and connection capacities stay with your engineer.
  • Steel: AS 4100 for design, AS/NZS 5131 for fabrication and erection, and AS/NZS 1554 for welding.
  • Concrete and loads: reinforcement drawings and bar schedules to AS 3600; wind and other loads as your engineer specifies.

Typical structural drafting jobs

The kind of work that comes through our structural team. Client work is covered by confidentiality, so project details are not published.

SOLIDWORKS + AutoCAD

Residential steel framing

Beams, columns and connections detailed with a bill of materials and DXF cutting files for the fabricator.
SOLIDWORKS

Sheds and light industrial buildings

Portal and cold-formed frames with weldment, beam, plate and assembly shop drawings.
SOLIDWORKS

Decks and stairs

Deck framing, stair assemblies and handrails modelled from the engineer’s sketches and issued as shop drawings.
Tekla

Steel shop detailing packages

General arrangement, assembly and single-part drawings, NC files, material lists and IFC exports.
SOLIDWORKS

Skids, platforms and pipe supports

Skids, pipe supports, canopies, walkways, stairs, handrails and grating.
Inventor

Commercial steel detailing

Set-out, steelwork and purlin layouts with hollow-section framing and member schedules.

How a job runs

Step 1

Send what you have

Sketches, marked-up PDFs, photos, models or existing drawings. We confirm the scope and quote within one business day.

Step 2

Drafting and checking

Drawn in your title block and layer standard, then checked against your source material before it is issued.

Step 3

Review and final issue

You mark up the review set, we pick up the comments and issue the final drawings and files.

Structural drafting in Brisbane: frequently asked

Do you have a Brisbane office?

Yes. Our core team is based in Brisbane, and you can reach it on 07 3149 3547.

Do your drawings need to be signed off by an RPEQ?

The engineering does. Queensland law requires professional engineering services to be carried out by an RPEQ or under one’s direct supervision, so member sizes and connection design come from your engineer. We detail to that design and return the set for their review.

Do you do the structural design?

No. Member sizes and connection capacities come from your engineer. We detail to their design and tell you early if something on the drawings does not fit.

What do you need to quote a structural drafting job?

Whatever you have: sketches, marked-up PDFs, photos, a sample part or existing CAD files. We come back with a no-obligation quote within one business day.

What files do we get back?

DWG and PDF drawings, DXF or NC files for the cutting line, a material list, and an IFC model where the job is modelled in 3D.

More on this service: structural drafting services across Australia. Other disciplines for local projects: CAD drafting services in Brisbane.

Send the drawings or a sketch.
Quote within one business day.

Call 07 3149 3547 or send your brief for a no-obligation quote.

Get a free quote — 1800 287 223